The HyGrade design with the farmer in mind

Models 800, 800RS, 1000, and 1000RS have:

  • All hydraulic cylinders, hoses, and tips are included.
  • All hydraulic cylinders have nitro steel shafts.
  • Available in 8′ and 10′ blade lengths.
  • Blade tilts 15 degrees left and right for slope cuts.
  • Blade angles 40 degrees left and right
  • On Models 800/1000, all three hydraulic functions can operate from one remote.
  • Models 800RS/1000RS require one additional remote to operate rear steer functions.
  • Concrete weight, box scraper ends are standard with each model.
  • Reversible / replaceable high carbon steel cutting edge.
  • Deep Tri Rib tires have excellent side bite traction.
  • Excellent blade to ground clearance.
    Storable hitch jack.
    Safety chain is included.
Specifications
MODEL8001000
BladeBlade Length8′10′
 Blade Angle40°40°
 Blade Height17″17″
 Blade Tilt15°15°
 Blade to Ground Clearance15″15″
Tires Two Tri Rib 5.00 x 15″, 4 plyTwo Tri Rib 5.00 x 15″, 4 ply
Hubs and Spindles 1500# 4 bolt1500# 4 bolt
Total Weight 1880#1960#
Tongue Weight 480#550#
Transport Width 7′ 1″8′ 10″
Cutting Width at 40° Angle 6′ 5″7′ 11″
Overall Length 16′ 2″16′ 2″
HP Range 25 – 10025 – 100

ALL THREE HYDRAULIC FUNCTIONS CAN OPERATE FROM ONE REMOTE.

Models 800 and 1000 come equipped with one of the following three options:

3 button handle (operates off of one remote)
3 switch control box (operates off of one remote)
6 hoses (for tractors with 3 remotes)

Models 800RS and 1000RS HyGrade Grader / Box Scraper

Model 1000RS

Model 1000RS with box ends tipped
down to convert to a box scraper

Swivel hitch for Models 800, 800RS, 1000, and 1000RS

1000RS steered to the right
1000RS steered to the left

The models 800RS and 1000RS have Hydraulic Rear Steer that allows the operator to move the blade approximately 3 feet more to the left or the right side of the tractor. All done hydraulically from the tractor seat.
These Rear Steer models require a minimum of 2 hydraulic remotes.

This rear steer feature allows the HyGrade Grader to clean among bunk lines, feedlot fences, in poulrty barns, around buildings, road edges, trees, etc. without having to drive the tractor so close to the objects that you are working near.

The Rear Steer feature gives the grader the capability to clean out drainage or irrigation ditches that are wet, while keeping the tractor on dryer ground. The Rear Steer models are very useful in orchards where reaching under trees is necessary.

Specifications
MODEL800RS1000RS
BladeBlade Length8′10′
 Blade Angle40°40°
 Blade Height17″17″
 Blade Tilt15°15°
 Blade to Ground Clearance12″12″
Tires Two Tri Rib 5.00 x 15″, 4 plyTwo Tri Rib 5.00 x 15″, 4 ply
Hubs and Spindles 1500# 4 bolt1500# 4 bolt
Total Weight 2160#2240#
Tongue Weight 520#590#
Transport Width 6′ 8″8′ 5″
Cutting Width at 40° Angle 6′ 5″7′ 11″
Overall Length 18′18′
HP Range 25 – 10025 – 100

To operate the functions of blade angle, tilt, and lift;
Models 800RS and 1000RS come equipped with one of the two following options:

3 Switch Control Box (operates off of one remote)
3 Button Handle (operates off of one remote)
A second remote is required for the rear steer functions