Landscaping

V60 ROOT RAKE GRAPPLE

Two-cylinder, single jaw grapple for digging, raking, piling and loading debris.

Unique design allows efficient forward and reverse operation to drag loose material into piles.
Heavy-duty jaw and rake tines constructed from 1/2″ Grade 80 steel.
50.3” grapple jaw opening to haul large amounts of brush per load.
Series 23 replaceable cast teeth.
2 1/2ˮ bore, 8 3/8” stroke cylinders featuring corrosion, dent and flake resistant NitroSteel® cylinder rods.
Greasable 1 1/4” diameter cylinder pins and 1 9/16” diameter hinge pins.
Teflon® coated bushings provide lubrication at all pivot locations.
Machine specific hydraulic package to completely protect hose routing.
Known clearance issue with RRG72 on Takeuchi track loaders and John Deere® G-Series loaders (330G, 331G, 332G, and 333G).

TRENCHER

Designed to quickly and reliably dig trenches 36, 48, or 60 inches deep.

Direct drive Eaton® motor reduces downtime, no chains or belts. Standard flow and high flow motor options available.
Standard manual side-shift allows operator to dig near structures and other objects.
Adjustable and removable auger clears loose soil from the trenching area.
Standard crumber designed to keep the trench bottom clean and smooth.
Chain also rotates in reverse to expel obstructions and chain tension can be quickly adjusted.
Multiple chain configurations available for trenching in soft, hard, rocky, or frozen ground to get the job done quicker.
Multiple digging depths and chain widths available. See chart below.

POWER RAKE

Grade, rake and remove debris all with one attachment.

Direct drive Eaton® motor reduces downtime and is guarded from damage.
Floating design keeps the rake level for a smooth, even finish.
Bi-directional drum works the soil in both directions for quick seedbed preparation.
Manually angle the rake 25 degrees in either direction. Hydraulic Angle option available.
Standard carbide tip teeth for long life in many soil conditions.
Standard removable end plates help contain raked debris.
Solid urethane filled tires eliminate costly interruptions from flats.

TREE BOOM

Adds 46 1⁄2” (from top of quick tach) to the lifting height of the machine.

Front of the frame is flat to prevent damage to trees during transport.
Use the holes in the sides of the frame to strap down and secure loads.
Pole is reinforced with three large gusset plates and two plates at the base.
Two 1/2” steel plates at the top of the boom with holes allow multiple rigging options.

TREE PULLER

Jaws open to 11.5” to quickly pull out trees and fence posts.

Hard stop at tip keeps small space between teeth when fully closed. This allows even small trees to be pulled without shearing them off.
Single hydraulic cylinder is protected from debris and other objects.
Corrosion, dent and flake resistant NitroSteel® cylinder rod made in the USA.

U-BLADE

Patented dual-point blade design enables digging and trenching in forward and reverse.

Numerous uses including transplanting trees, digging rocks, trenching, and breaking up compacted soil.
Open design provides excellent visibility and ensures the operator can quickly transplant trees, often without the help of others.

STUMP BUCKET

A versatile attachment ideal for digging stumps and rocks, trenching, and breaking up compacted soil.

Tall sides provide capacity, while compact depth provides leverage to pry under stumps and rocks.
Three flush mount shanks, with replaceable Series 23 cast teeth, welded to a 3/4” x 6” weld-on wear edge.
Bucket is reinforced on each side with three large gusset plates.
Stump Bucket Grapple also available.

STUMP BUCKET GRAPPLE

A versatile grapple ideal for digging stumps and rocks, trenching and breaking up compacted soil.

Grapple jaw makes stump and rock removal easier and secures load for transport.
Tall sides provide capacity, while compact depth provides leverage to pry under stumps and rocks.
Corrosion, dent and flake resistant NitroSteel® cylinder rod made in the USA. Cylinder Guard standard.
Three flush mount shanks, with replaceable Series 23 cast teeth, welded to a 3/4” x 6” weld-on wear edge.
Bucket is reinforced on each side with three large gusset plates.
Stump Bucket without grapple also available.

DOZER BLADE – 6 WAY

Six-way dozer blade with heavy-duty frame, 3/8″ thick moldboard and adjustable skid shoes.

Two-cylinder hydraulic angle and one-cylinder hydraulic tilt utilizing one electric valve and one loader valve.
Corrosion, dent and flake resistant NitroSteel® cylinder rods made in the USA.
2 1/8” hinge and oscillation pins, replaceable Teflon® coated bushings provide lubrication at all pivot locations.
5/8” x 8” reversible, replaceable bolt-on wear edge.
NOTE: Does not have a trip edge or trip moldboard.

TILLER

Bi-directional, direct drive tiller attachment with a bearing supported shaft and replaceable tines.

Bi-directional rotation allows tilling going forward or in reverse.
Direct drive motor eliminates chains or belts reducing maintenance and downtime.
Tillers shaft supported on both ends by 2″ diameter bearings minimizing weight held by the motor.
Motor guarded on bottom and sides for added protection against rocks and debris.
Replaceable, heat-treated, dual-edge tines help break through clumps and tear through hard ground.
Offset to cover tire tracks, and allows the operator to till next to buildings, sidewalks, etc.

LAND LEVELER

Makes leveling uneven ground easy and efficient.

Two reversible, replaceable bolt-on wear edges and sturdy construction permits aggressive cutting, while wide blade location allows precise control for a smooth finish.
Use for a variety of grading projects. No rake required.

V40 AUGER DRIVE

Supports auger bits up to 30″ in diameter.

Planetary gear reduction assures consistent high torque output and long lifetime usage.
Parker® motor with an integrated hydraulic pressure relief valve for protection against pressure spikes.
2″ hex output provides a stronger, more durable interface.

V50 AUGER DRIVE

Heavy-duty frame with hex output that supports auger bits up to 36” in diameter.

Planetary gear reduction assures consistent high torque output and long lifetime usage.
Parker® motor with hydraulic pressure relief valve.
2” hex output providing stronger, more durable interface.

AUGER BITS

Auger bits from 6” to 36” in diameter to satisfy a variety of needs.

STANDARD (SAV) & TREE BITS (TAV)

For light to moderate ground conditions.
One piece fabricated steel boring head.
Double flighting with replaceable bolt-on teeth.
4′ overall length with 2″ hex collar input.
Tree bits are smaller at the bottom to better keep trees in place while planting.
Variety of tooth options available.
Auger extensions and adapters available.

ROCK BITS (RAV)

For solid and fracturable rock, compacted soils, frozen ground, asphalt and concrete.
Cast steel boring head.
Single flighting with replaceable bullet teeth.
4′ overall length with 2″ hex collar input.
Standard with Rotating Bullet Teeth and CDR Rock Pilot.

V50 MULTI-PURPOSE BUCKET (4-IN-1)

Multiple functions in one attachment to save time and money.

Functions include dozing, clamming, leveling, and bottom dumping.
Large 33” opening for easier, more efficient operation.
Design provides effective dozing, while maintaining maximum visibility.
¾” x 6” weld on edge on front of bucket accepts optional edges.
Corrosion, dent and flake resistant NitroSteel® cylinder rods made in the USA. Cylinder Guards standard.
V60 Multi-Purpose Bucket also available.
Commonly called a 4-in-1 bucket.

V60 MULTI-PURPOSE BUCKET (4-IN-1)

Multiple functions in one attachment to save time and money. Stronger than the V50 Multi-Purpose Bucket.

Functions include dozing, clamming, leveling, and bottom dumping.
Large 33” opening for easier, more efficient operation.
Design provides effective dozing, while maintaining maximum visibility.
HMPV models have 1/4″ shell, 1-2 extra wear bars underneath, additional bracing, 1/2″ hinge structure and reinforcement at rear corners of dozer and quick-tach plate.
¾” x 6” weld-on edge on front of bucket accepts optional edges.
Corrosion, dent and flake resistant NitroSteel® cylinder rods made in the USA. Cylinder Guards standard.
Commonly called a 4 in 1 bucket.